Tuesday, January 28, 2014

DIY Pitching Mound

We have two boys (7 and 11) and from the beginning of April until the end of July it's baseball 24-7 at our house.  By the end of the season the lawn is bare where the kids have setup their make shift pitching mound.  I decided to remedy that by building a wooden mound instead.  I wanted to build something large enough that the kids could grow into it, but still portable enough to move it now and then.  I also wanted to be able to use it inside during the winter in the basement.

Here's what I ended up building:




Materials list:

  • 3 - 2x6x10ft treated lumber
  • 1 - 2x6.x8ft treated lumber
  • 1 - 2x4x8ft treated lumber
  • 1 - 4x8x1/2 treated plywood
  • 1 - box 1 1/4" coated deck screens
  • 1 - box 3" coated deck screws
  • 1 - pitching rubber (Amazon)
  • 7 - 1/2" reversible foam mats 
  • 1 - tube foam adhesive
The dimensions of the mound are 84" x 42".  The end with the pitching rubber is the full width of a 2x6 (~5 1/2" ) and it tapers down to 2" at the bottom.  I choose that height because in little league the mound is 6" above home plate.  The flat section with the rubber is 22" inches wide before it begins to taper.


  
I cut away a section from the sides and back of each board to help reduce the weight and to also give the grass underneath the mound a chance to breathe.  It also makes it much easier to lift up if you need to move it.  I plan add some portable wheels eventually, but I'll worry about that this spring when it's time to move it :)

Here are a few more pictures from different angles:



You can see from the picture below that I set the bottom of the plywood 7/8" of an inch below the top of the 2x6's.  That way when I added the 1/2" foam it would be roughly flush with the top. The pitching rubber is 3/4" of an inch thick so it sits above the foam slightly.  I debated on adding an extra piece of wood below the rubber to raise it up a bit more, but I figured that the foam would compress some after use.


The reason that I used foam rubber tiles is because I had a bunch of them laying in my garage collecting dust.  I considered indoor/outdoor carpet, but I thought the kids would appreciate having a bit more cushion.  I also seriously consisted buying a cheap rubber stall mat, but the mat alone was close to 70 pounds.
\

He's an angle from the bottom and as you can see it's not very pretty. If I had had some extra 2x4's laying around I would have built a 1 1/2" continuous frame around the perimeter to support the plywood.  Instead I simply used the scrape pieces that I had left over from side and back cutouts. It seems to be plenty stable for the kids, so it worked out OK.  You can't tell from the pictures, but I also drilled some drainage holes at the bottom of the mound.



 Hopefully someone will find this useful.  We'll see you in Williamsport (go Coon Rapids Andover American Little League!)

Wednesday, February 22, 2012

Man Vs. Mosquito live on Android Market!

We just launched our first Android using the AndEngine game engine. Check it out at the Android market here:

Man Vs. Mosquito

Sunday, November 21, 2010

Garminfone hard plastic case

I recently purchased a Garminfone from T-Mobile.  I made the switch from an iPhone 2G because I dropped the iPhone and cracked the screen.   After that experience I decided that it wasn't going to happen to my Garminfone. Unfortunately, the Garminfone hasn't sold very well so there aren't very many companies making cases for it.  I decided to try a case from Ebay that's sold by Wireless Accessories.  If you search on eBay for "garminfone case fire burn orange" you will find it.

Here are a few pictures.







I couldn't find any reviews on the case so I wasn't sure what to expect.  The case is relatively attractive and it comes in a variety of colors.  The case material is a hard plastic and it comes in either a shiny or rubberized finish.  I went with the rubberized version because I didn't want it slipping out of my hand.  The case comes in two pieces that snap together.  Once you snap it together it's really difficult to get apart again.   The phone fits very snugly in the case.  The openings for the speaker and camera are well placed and the case isn't terribly bulky.

Unfortunately, those are the only nice things that I can say about it.  When I bought it I figured that it probably wouldn't work with the stock car mount.  From the 3rd picture you can see that there's a round hump on the back of phone.  This is apparently designed to be used with a belt clip.  The problem is that it sticks out about an 1/8 of an inch.  Without a case the phone snaps tightly into the car mount, but with the case it's too thick.  On top of that the opening for the mount isn't wide enough (see picture 4).  The mount is about 1/2 of an inch wider than the opening in the case.  I don't even know why they bothered cutting an opening for it.

The first thing that I noticed when I put the phone into the case was that it was really hard to turn the phone on.  The case fits very snugly, and the opening for the power button is large enough to easily access the button.  It's really hard to explain, but the case compresses the phone in manner that makes the button not work properly.  Without the case the power button will move about 1/6 of an inch.  With the case it moves less than 1/32 of an inch so it's really frustrating to use.  I get the distinct impression that the manufacturer never actually tried the case on a real phone.   They must have only tested it against a demo phone.  This flaw pretty much makes the case worthless.

So to summarize:

Good:
  • Looks nice
  • Solidly built with a nice feel
  • Slim fitting case
  • Cheap ~$8
Ugly:
  • The case is too thick to use with the stock mount
  • THe opening in the case it too narrow for the car mount
  • The case is too snug so you can't turn on the phone properly.

Friday, July 23, 2010

House listed on MLS

You can now find the property on MLS by searching for number MLS# 3951123.  Here's a direct link to the Edina Reality site: Edina Reality Listing.

Monday, May 31, 2010

House listed on Zillow.com

I listed the house on Zillow.com.  We haven't listed the house on MLS yet, but we have been getting steady traffic from people driving past that see for sale sign.  Here's the zillow link:

http://www.zillow.com/homedetails/31065-360th-St-Laporte-MN-56461/2131554206_zpid/

Tuesday, May 18, 2010

Part 24 - Deck

The deck is done.  The steps off the corner of the deck turned out great.

Sunday, May 2, 2010

Part 23 - For Sale By Owner

We officially put up the for sale sign today.  The project has gone incredibly well, and so far we have gotten rave reviews from the people that have looked at it.  Hopefully we'll be able to match the house up with the right buyer.

There are still a few items that we need to be finished, but we are getting very close.  Carpet, garage slab and deck are the next items on the list.  Here are some updated photos:

The cherry mantel turned out wonderful.  It's a perfect match with the kitchen cabinets, and it ties the two rooms together nicely.  Linda did a great job of matching the stain.

We plan to paint the front door to match the soffit.  The lovely door ramp will soon be replaced by a wrap-around deck :)


We now have kitchen and bathroom fixtures.  We've had running water outside for weeks, but we still need to hook up the water inside.
The cat-5 patch panel is installed in the hallway closet.  The house is very media friendly.  We wired it for ethernet and TV, and ran conduit to the future TV above the fireplace.

All of the closest in the house now have shelves.  The photo above is a shot of the pantry.

The pine doors are varnished and they look incredible.  It gives the house a very warm feeling.

Thursday, April 15, 2010

Part 22 - Siding is on

Since the last post there has been a ton of progress on the exterior of the house.  We chose to install a pre-finished fiber cement lap siding from James Hardie (HardiPlank).  For the gables, we went with darker vinyl shakes.

The wrap-around deck, garage apron, lighting, and landscaping are the last items left to complete the exterior.

The slate fireplace is also finished except for the cherry mantle. It turned out really nice.  

Sunday, March 28, 2010

Part 21 - Countertop

For the countertop we decided to go with Formica Laminate (Butterum granite).  The color goes really well with the Cherry cabinets.  The island was designed so that one person could sit at a stool comfortably on the end with the corbels (12" overhang) or  two people could sit on the dining room side if necessary (6" overhang).  We really wanted an island, but we also didn't want to take too much space away from the dining room.  The island configuration was a decent compromise.



For the 48" vanity bathroom we went with a beige granite top.  In the picture below, the vanity top is raised up so that the vanity could be stained without messing up the granite.


The vanity should complement the tile accents that we are planning for the bathroom.



Sunday, March 21, 2010

Part 20 - Doors, Lights, and Crown Molding

More progress since the last post.  The most noticeable changes include light fixtures, six panel pine doors and crown molding on the cabinets.  Here are some shots:



Friday, March 12, 2010

Part 19 - Tile is installed

The tile is installed, grouted and sealed.  It turned out great.  We are really happy with the tile color.  It looks really nice with the cabinets.

Tuesday, March 2, 2010

Part 18 - Tiling begins

With the tile search completed, the guys started prepping the floor. The floor immediately above the floor joist is OSB, which isn't what you want under the cement hardibacker board. To prevent bubbling from moisture, the hardibacker should be installed on top of an exterior grade plywood.  The cement board is installed on top of the plywood with with thinset and screws.  This makes for a very solid floor which is important because we are using 18x18 porcelain tile.  Flexing in the floor could cause the tile to crack.

Here are a few shots of the finished subfloor.  You will notice that the seams haven't been taped yet in these pictures.


Here's a shot of the tile in the laundry/mud room.  The lines look to be nice and straight :)





Tuesday, February 23, 2010

Part 17 - Cabinets

The cabinets arrived on Monday, and the guys didn't waste any time getting them installed.  They are 36" cherry with a cranberry stain and black glaze.  The drawers have self closing hardware which is nice feature.  We opted for cherry to provide a nice contrast with the light pine ceiling.


Here's what the crown molding will look like once it's installed and dusted :)

Here's a shot of the 2'x4' island still in the box.


We haven't decided on the counter top yet. We will likely hold off on a decision until after the tile flooring is installed so that we can choose something that coordinates.

Saturday, February 20, 2010

Part 16 - Tile options

When we started this project I had envisioned using hardwood flooring for a big portion of the house.  People that live in the area started telling us that we were crazy to use hardwood.  The soil in the area is very sandy, so sand would be constantly be coming into the house.  Sand + hardwood doesn't make a very good combination.  It took some convincing, but I finally agreed.  We decided to go with tile instead.

The tile stores near the house consist of Home Depot and a couple of smaller tile/carpet shops.  We were looking for 16x16 tile, so that limited the selection even further.  I started out looking for tile in the Twin Cities to try to get an idea for price.  After nearly a million trips to tile stores, I came across an 18x18 discontinued tile at Home Depot that I really liked.  The price was right and the color was nice.  We called the Home Depot closest to the job site, and of course they didn't have any.  The closest store was 70 miles away and they only had 350 sq/ft, but we needed ~500 sq/ft.  We decide to buy what they had and pick up the rest in the cities.

At the store they wrapped up the 19 cases and my dad took them home.  When he unpacked them he discovered that 8 of the 19 cases were damaged.  Every tile in 8 of the cases were cracked.  Apparently a fork lift driver dropped them or something.  He called the store and they agreed to take back all of the tile (at the original store 70 miles away).  We took this as a sign that maybe we needed to look for a different tile.

Hopefully we'll find something soon, because we were hoping to start tiling next week.



  

Friday, February 19, 2010

Part 15 - Paint

Lots of progress since the last update. Check out the pictures below:

Guest bedroom (above) - Living Room (Below)

The picture below is a view of the kitchen and hallway leading to the back of the house.  The walls are primed and the tongue and groove pine ceiling is installed.

Here are some shots of the finished paint.  The pine ceiling also has 3 coats of poly.  The color is Glidden summer sandcastle.
Painting the closet.  Looks like fun.
View of the kitchen.